These NSF Official Listings are current as of Tuesday, May 21, 2013 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://nsf.org/Certified/PwsComponents/Listings.asp?Company=46690&Standard=061&
NSF/ANSI STANDARD 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings.
| Tnemec Company, Inc. | |
| 6800 Corporate Drive | |
| Kansas City, MO 64120-1372 | |
| United States | |
| 816-474-3400 | |
| Visit this company's website |
Facility : Baltimore, MD
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| 22 Epoxoline[1] | 1/2" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[2] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[3] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[2] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, B8039 Baker Blue, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, 15BL Tank white, 39BL Delft Blue, 35GR Black, B2506
DeZurik Blue, B7896 S-B Blue, 00WH Tnemec White, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of series 22, FC22, N140, or 141 may be substituted
as a primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. Mix ratio of Part A:Part B is 1:1 by
volume.
|
||||
|
Coatings - Pipe |
||||
| 22 Epoxoline[1] | >= 1/2" | CLD 23 | EPOXY | |
| Series 406 Elastoshield[5] | >= 36" | CLD 23 | PUR | |
| Series N140 Pota-Pox Plus[2] | >= 18" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[3] | >= 18" | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[2] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, B8039 Baker Blue, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, 15BL Tank white, 39BL Delft Blue, 35GR Black, B2506
DeZurik Blue, B7896 S-B Blue, 00WH Tnemec White, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of series 22, FC22, N140, or 141 may be substituted
as a primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. Mix ratio of Part A:Part B is 1:1 by
volume.
[5] Colors: WH06 Off-White
Number of Coats: 1-2
Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
Maximum Field Use Dry Film Thickness (in mils): Primer-10; Topcoat-75
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 72 hours at 75°F
Special Comments: Mix ratio for primers must meet their individual certified parameters.
Mix ratio of A:B is 1:2 by volume for Topcoat. Approved primers are V140 Pota-Pox Plus,
V140F Pota-Pox Plus Fast Cure, Series N140F Pota-Pox Plus Fast Cure, Series 140 Pota-Pox
Plus, FC20HS or F020HS.
|
||||
|
Coatings - Pump |
||||
| 22 Epoxoline[1] | 1/2" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[2] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[3] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[2] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, B8039 Baker Blue, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, 15BL Tank white, 39BL Delft Blue, 35GR Black, B2506
DeZurik Blue, B7896 S-B Blue, 00WH Tnemec White, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of series 22, FC22, N140, or 141 may be substituted
as a primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. Mix ratio of Part A:Part B is 1:1 by
volume.
|
||||
|
Coatings - Tank |
||||
| 22 Epoxoline[1] | >= 5 gal. | CLD 23 | EPOXY | |
| Series 20 Pota-Pox[4] | >= 6000 gal. | CLD 23 | EPOXY | |
| Series 406 Elastoshield[5] | >= 50,000 gal. | CLD 23 | PUR | |
| Series 91-H2O™ Hydro-Zinc™[6] | >= 8000 gal. | CLD 23 | PUR | |
| Series 94-H2O Hydro Zinc[7] | >= 200 gal. | CLD 23 | PUR | |
| Series FC20 Pota-Pox (Fast Cure)[8] | >= 6000 gal. | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[9] | >= 1000 gal. | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[10] | >= 1000 gal. | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[4] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 00WH White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Themec No. 4 Thinner by volume
Recoat Cure Time and Temperature: 12 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any Listed color of Series FC20, N140, N140F, 141 or 22 may be
substituted as a topcoat primer Mix ratio of Part A:Part B is 1:1 by volume.
[5] Colors: WH06 Off-White
Number of Coats: 1-2
Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
Maximum Field Use Dry Film Thickness (in mils): Primer-10; Topcoat-75
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 72 hours at 75°F
Special Comments: Mix ratio for primers must meet their individual certified parameters.
Mix ratio of A:B is 1:2 by volume for Topcoat. Approved primers are V140 Pota-Pox Plus,
V140F Pota-Pox Plus Fast Cure, Series N140F Pota-Pox Plus Fast Cure, Series 140 Pota-Pox
Plus, FC20HS or F020HS.
[6] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
coating system providing that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A:Part B is 70%:30% by volume.
[7] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[8] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 39BL Delft Blue, 00WH White
Number of Coats: 2-3
Sequence of Coats: Any combination of listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec No. 4 by volume
Recoat Cure Time and Temperature: 3 hours at 75°F
Final Cure Time and Temperature: 6 days at 75°F
Special Comments: Any Listed color of series 20, N140, N140F, 141 or 22 may be
substituted as the topcoat or primer. Mix ratio of Part A:Part B is 1:1 by volume.
[9] Colors: 1211 Red, 1255 Beige, 15BL Tank white, 39BL Delft blue, 35GR Black, Y2606 Romac
Yellow, B5712 Blue, B8039 Baker Blue, 00WH Tnemec White
Number of Coats: 1-3
Sequence of Coats: Any combination of Listed Colors
Maximum Field Use Dry Film Thickness (in mils): 1 coat - 10, 2-3 coats - 17 for Tnemec
Thinner #4 or Thinner #60
Maximum Thinner: 10% Tnemec No. 4 Thinner by volume or 5% Tnemec No. 60 Thinner by
volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any Listed color of Series 20, FC20, 22, FC22, N140F, V140, V140F,
L140, L140F, or 141 may be substituted for the Series N140 Pota-Pox Plus provided that
both primer and topcoat meet their individual Certified end uses. The mix ratio of Part
A: Part B is 1:1 by volume. Part C (Series 44-700 Accelerator) is an optional additive
to Part A in the field and may be added at up to 4 fluid ounces per two mixed gallons of
parts A and B.
[10] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft blue, 35GR Black, B7896 S-B
Blue, Y2606 Romac Yellow, 00WH Tnemec White, B5712 Blue
Number of Coats: 1-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 1 Coat - 10, 2-3 coats - 17 for Tnemec
Thinner #4 or Thinner #60
Maximum Thinner: 10% Tnemec No. 4 Thinner by volume or 5% Tnemec No. 60 Thinner by
volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any Listed color of Series 20, 22, 141, FC20, FC22, L140, L140F,
N140, V140, or V140F may be substituted as the topcoat for the Series N140F Pota-Pox
Plus provided that both primer and topcoat meet their individual Certified end uses.
The mix ratio of Part A: Part B is 1:1 by volume.
|
||||
|
Coatings - Valve |
||||
| 22 Epoxoline[1] | >= 1/2" | CLD 23 | EPOXY | |
| Series 406 Elastoshield[5] | >= 4" | CLD 23 | PUR | |
| Series N140 Pota-Pox Plus[2] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[3] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[2] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, B8039 Baker Blue, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, 15BL Tank white, 39BL Delft Blue, 35GR Black, B2506
DeZurik Blue, B7896 S-B Blue, 00WH Tnemec White, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of series 22, FC22, N140, or 141 may be substituted
as a primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. Mix ratio of Part A:Part B is 1:1 by
volume.
[5] Colors: WH06 Off-White
Number of Coats: 1-2
Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
Maximum Field Use Dry Film Thickness (in mils): Primer-10; Topcoat-75
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 72 hours at 75°F
Special Comments: Mix ratio for primers must meet their individual certified parameters.
Mix ratio of A:B is 1:2 by volume for Topcoat. Approved primers are V140 Pota-Pox Plus,
V140F Pota-Pox Plus Fast Cure, Series N140F Pota-Pox Plus Fast Cure, Series 140 Pota-Pox
Plus, FC20HS or F020HS.
|
||||
Facility : North Kansas City, MO
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| 22 Epoxoline[1] | 1/2" | CLD 23 | EPOXY | |
| Series 141 Epoxoline[2] | >= 1/2" | CLD 23 | EPOXY | |
| Series 141 Epoxoline[3] | >= 3/4" | CLD 23 | EPOXY | |
| Series F020HS[4] | 1/2" | CLD 23 | EPOXY | |
| Series FC20HS[4] | 1/2" | CLD 23 | EPOXY | |
| Series L140 Pota-Pox Plus[5] | >= 1" | CLD 23 | EPOXY | |
| Series L140F Pota-Pox Plus Fast Cure[6] | >= 1" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[7] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[8] | >= 4" | CLD 23 | EPOXY | |
| V140 Pota-Pox Plus[9] | >= 3/4" | CLD 23 | EPOXY | |
| V140F Pota-Pox Plus Fast Cure[10] | >= 3/4" | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[2] Colors: 1255 Beige, WHO3 White, 1211 Red Primer, B2506 DeZurikBlue, B7011 Crispin Blue,
33GR Gray, 35GR Black, and 39BL Delft Blue, B2592 RAL 5009 Azurblau
Number of Coats: 1-3
Sequence of Coats: Any order
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec No. 4 Thinner or 5% Tnemec No. 60 Thinner
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: This application is to be used with pipes 10" and greater, fittings
1/2" and greater, valves 2" and greater, and pumps 4" and greater. Any listed color of
FC20HS, F020HS, Series 20, FC20, FC22, N140, N140F, L140, L140F, V140, or V140F may be
substituted for Series 141 Epoxoline topcoat. Mix ratio of Part A to Part B is 2:1 by
volume.
[3] Colors: 1255 Beige, WHO3 White, 1211 Red Primer, 33GR Gray, 35GR Black, 39BL Delft Blue,
B2592 RAL 5009 Azurblau, and and B8039 Baker Blue
Number of Coats: 1-2
Sequence of Coats: Any order
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec #4 Thinner or 5% Tnemec #60 Thinner
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of FC20HS, F020HS, Series 20, FC20, FC22, N140,
N140F, L140, L140F, V140, or V140F may be substituted for the Series 141 Epoxoline
Primer or Topcoat provided that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A to Part B is 2:1 by volume. These application parameters
are Certified for tanks 200 gallons and greater, pipe 14" and greater, fittings 3/4" and
greater, and valves and pumps 3.5" and greater.
[4] Colors: 1255 Beige Primer, WH12 White, 15BL Tank White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% No. 4 Thinner (F041-0004)
Recoat Cure Time and Temperature: 6 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of Series 20, FC20, N140, N140F, L140, L140F, V140,
V140F may be substituted for the Series FC20HS or F020HS Pota-Pox topcoat or primer
provided that both primer and topcoat both meet their Certifed end uses. Mix ratio of
Part A:Part B is 1:1 by volume.
[5] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 15 (maximum of 5 mils per coat)
Maximum Thinner: 5% Tnemec No. 49 Thinner by volume
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140 provided that both primer and topcoat meet
their individual Certified end uses. Series 44-700 accelerator (Part C) may be added up
to 4 fluid ounces per two mixed gallons of L140 Parts A and B. Mix ratio of A:B is 1:1
by volume.
[6] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 2-3
Sequence of coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 15 (maximum of 5 per coat)
Maximum Thinner: 5% Tnemec No. 49 by volume
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
their individual Certified end uses. Mix ratio of Part A to Part B is 1:1 by volume.
[7] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[8] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, B2506
DeZurik Blue, B7896 S-B Blue, 00WH Tnemec White, Y2606 Romac Yallow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume.
[9] Color: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 1-3
Maximum Field Use Dry Film Thickness (in mils): 1 coat - 10, 2-3 coats - 18
Maximum Thinner: 5% Tnemec No. 4 by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comment: Mix ratio of Part A to Part B is 1:1 by volume. Series 44-700 (Part C)
may be added up to 4 fl. oz. per gallon. Any listed color of Series 20, FC20, N140,
N140F, L140, L140F, V140F, 22 and 141 may be substituted as a topcoat or primer for
Series V140 provided that both primer and topcoat meet their individual Certified end
uses.
[10] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 00WH White
Number of Coats: 1-3
Maximum Field Use Dry Film Thickness (in mils): 1 coat: 10; 2-3 coats: 18
Maximum Thinner: 5% Tnemec #4 by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Any listed color of
Series 20, FC20, N140, N140F, L140, L140F, V140, 22, and 141 may be substituted as a
topcoat or primer for Series V140F provided that both primer and topcoat meet their
individual Certified end uses.
|
||||
|
Coatings - Pipe |
||||
| 22 Epoxoline[1] | >= 1/2" | CLD 23 | EPOXY | |
| Series 1 Omnithane 1216 Grayish-Green[11] | >= 36" | CLD 23 | PUR | |
| Series 141 Epoxoline[3] | >= 14" | CLD 23 | EPOXY | |
| Series 141 Epoxoline[2] | >= 10" | CLD 23 | EPOXY | |
| Series 406 Elastoshield[12] | >= 36" | CLD 23 | PUR | |
| Series F020HS[4] | 8" | CLD 23 | EPOXY | |
| Series FC20HS[4] | 8" | CLD 23 | EPOXY | |
| Series FC22 Epoxoline[13] | >= 1/2" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[7] | >= 18" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[8] | >= 18" | CLD 23 | EPOXY | |
| V140 Pota-Pox Plus[9] | >= 100" | CLD 23 | EPOXY | |
| V140F Pota-Pox Plus[10] | >= 100" | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[2] Colors: 1255 Beige, WHO3 White, 1211 Red Primer, B2506 DeZurikBlue, B7011 Crispin Blue,
33GR Gray, 35GR Black, and 39BL Delft Blue, B2592 RAL 5009 Azurblau
Number of Coats: 1-3
Sequence of Coats: Any order
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec No. 4 Thinner or 5% Tnemec No. 60 Thinner
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: This application is to be used with pipes 10" and greater, fittings
1/2" and greater, valves 2" and greater, and pumps 4" and greater. Any listed color of
FC20HS, F020HS, Series 20, FC20, FC22, N140, N140F, L140, L140F, V140, or V140F may be
substituted for Series 141 Epoxoline topcoat. Mix ratio of Part A to Part B is 2:1 by
volume.
[3] Colors: 1255 Beige, WHO3 White, 1211 Red Primer, 33GR Gray, 35GR Black, 39BL Delft Blue,
B2592 RAL 5009 Azurblau, and and B8039 Baker Blue
Number of Coats: 1-2
Sequence of Coats: Any order
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec #4 Thinner or 5% Tnemec #60 Thinner
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of FC20HS, F020HS, Series 20, FC20, FC22, N140,
N140F, L140, L140F, V140, or V140F may be substituted for the Series 141 Epoxoline
Primer or Topcoat provided that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A to Part B is 2:1 by volume. These application parameters
are Certified for tanks 200 gallons and greater, pipe 14" and greater, fittings 3/4" and
greater, and valves and pumps 3.5" and greater.
[4] Colors: 1255 Beige Primer, WH12 White, 15BL Tank White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% No. 4 Thinner (F041-0004)
Recoat Cure Time and Temperature: 6 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of Series 20, FC20, N140, N140F, L140, L140F, V140,
V140F may be substituted for the Series FC20HS or F020HS Pota-Pox topcoat or primer
provided that both primer and topcoat both meet their Certifed end uses. Mix ratio of
Part A:Part B is 1:1 by volume.
[7] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[8] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, B2506
DeZurik Blue, B7896 S-B Blue, 00WH Tnemec White, Y2606 Romac Yallow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume.
[9] Color: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 1-3
Maximum Field Use Dry Film Thickness (in mils): 1 coat - 10, 2-3 coats - 18
Maximum Thinner: 5% Tnemec No. 4 by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comment: Mix ratio of Part A to Part B is 1:1 by volume. Series 44-700 (Part C)
may be added up to 4 fl. oz. per gallon. Any listed color of Series 20, FC20, N140,
N140F, L140, L140F, V140F, 22 and 141 may be substituted as a topcoat or primer for
Series V140 provided that both primer and topcoat meet their individual Certified end
uses.
[10] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 00WH White
Number of Coats: 1-3
Maximum Field Use Dry Film Thickness (in mils): 1 coat: 10; 2-3 coats: 18
Maximum Thinner: 5% Tnemec #4 by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Any listed color of
Series 20, FC20, N140, N140F, L140, L140F, V140, 22, and 141 may be substituted as a
topcoat or primer for Series V140F provided that both primer and topcoat meet their
individual Certified end uses.
[11] Colors: 1216 Grayish-Green
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F
Special Comment: Series 44-710 may be added up to 4 fl. oz/gal. Approved for use as a
primer with any NSF Certified Tnemec topcoat or coating system provided that both primer
and topcoat meet their individual Certified end uses.
[12] Colors: WH06 Off-White
Number of Coats: 1-2
Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
Maximum Field Use Dry Film Thickness (in mils): Primer-10; Topcoat-75
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 72 hours at 75°F
Special Comments: Mix ratio for primers must meet their individual certified parameters.
Mix ratio of A:B is 1:2 by volume for Topcoat. Approved primers are V140 Pota-Pox Plus,
V140F Pota-Pox Plus Fast Cure, Series N140F Pota-Pox Plus Fast Cure, Series 140 Pota-Pox
Plus, FC20HS or F020HS.
[13] Colors: WH08 White
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: None
Final Cure Time and Temperature: 24 hours at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:2 by volume. Any Listed color of
series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
|
||||
|
Coatings - Pump |
||||
| 22 Epoxoline[1] | 1/2" | CLD 23 | EPOXY | |
| Series 141 Epoxoline[2] | >= 4" | CLD 23 | EPOXY | |
| Series 141 Epoxoline[3] | >= 3.5" | CLD 23 | EPOXY | |
| Series F020HS[4] | 1/2" | CLD 23 | EPOXY | |
| Series FC20HS[4] | 1/2" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[7] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[8] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[2] Colors: 1255 Beige, WHO3 White, 1211 Red Primer, B2506 DeZurikBlue, B7011 Crispin Blue,
33GR Gray, 35GR Black, and 39BL Delft Blue, B2592 RAL 5009 Azurblau
Number of Coats: 1-3
Sequence of Coats: Any order
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec No. 4 Thinner or 5% Tnemec No. 60 Thinner
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: This application is to be used with pipes 10" and greater, fittings
1/2" and greater, valves 2" and greater, and pumps 4" and greater. Any listed color of
FC20HS, F020HS, Series 20, FC20, FC22, N140, N140F, L140, L140F, V140, or V140F may be
substituted for Series 141 Epoxoline topcoat. Mix ratio of Part A to Part B is 2:1 by
volume.
[3] Colors: 1255 Beige, WHO3 White, 1211 Red Primer, 33GR Gray, 35GR Black, 39BL Delft Blue,
B2592 RAL 5009 Azurblau, and and B8039 Baker Blue
Number of Coats: 1-2
Sequence of Coats: Any order
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec #4 Thinner or 5% Tnemec #60 Thinner
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of FC20HS, F020HS, Series 20, FC20, FC22, N140,
N140F, L140, L140F, V140, or V140F may be substituted for the Series 141 Epoxoline
Primer or Topcoat provided that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A to Part B is 2:1 by volume. These application parameters
are Certified for tanks 200 gallons and greater, pipe 14" and greater, fittings 3/4" and
greater, and valves and pumps 3.5" and greater.
[4] Colors: 1255 Beige Primer, WH12 White, 15BL Tank White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% No. 4 Thinner (F041-0004)
Recoat Cure Time and Temperature: 6 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of Series 20, FC20, N140, N140F, L140, L140F, V140,
V140F may be substituted for the Series FC20HS or F020HS Pota-Pox topcoat or primer
provided that both primer and topcoat both meet their Certifed end uses. Mix ratio of
Part A:Part B is 1:1 by volume.
[7] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[8] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, B2506
DeZurik Blue, B7896 S-B Blue, 00WH Tnemec White, Y2606 Romac Yallow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume.
|
||||
|
Coatings - Tank |
||||
| 22 Epoxoline[1] | >= 5 gal. | CLD 23 | EPOXY | |
| Series 1 Omnithane 1216 Grayish-Green[11] | >= 1000 gal. | CLD 23 | PUR | |
| Series 141 Epoxoline[3] | >= 200 gal. | CLD 23 | EPOXY | |
| Series 20 Pota-Pox[14] | >= 6000 gal. | CLD 23 | EPOXY | |
| Series 215[15] | >= 200 gal. | CLD 23 | EPOXY | |
| Series 406 Elastoshield[12] | >= 50,000 gal. | CLD 23 | PUR | |
| Series 91-H2O™ Hydro-Zinc™[16] | >= 8000 gal. | CLD 23 | PUR | |
| Series 94-H2O Hydro Zinc[17] | >= 200 gal. | CLD 23 | PUR | |
| Series F020HS[4] | >= 25 gal. | CLD 23 | EPOXY | |
| Series FC20 Pota-Pox (Fast Cure)[18] | >= 6000 gal. | CLD 23 | EPOXY | |
| Series FC20HS[4] | >= 25 gal. | CLD 23 | EPOXY | |
| Series FC22 Epoxoline[19] | >= 5 gal. | CLD 23 | EPOXY | |
| Series L140 Pota-Pox Plus[5] | >= 50,000 gal. | CLD 23 | EPOXY | |
| Series L140F Pota-Pox Plus Fast Cure[6] | >= 50,000 gal. | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[20] | >= 1000 gal. | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[21] | >= 1000 gal. | CLD 23 | EPOXY | |
| V140 Pota-Pox Plus[9] | >= 50,000 gal. | CLD 23 | EPOXY | |
| V140F Pota-Pox Plus Fast Cure[10] | >= 50,000 gal. | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[3] Colors: 1255 Beige, WHO3 White, 1211 Red Primer, 33GR Gray, 35GR Black, 39BL Delft Blue,
B2592 RAL 5009 Azurblau, and and B8039 Baker Blue
Number of Coats: 1-2
Sequence of Coats: Any order
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec #4 Thinner or 5% Tnemec #60 Thinner
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of FC20HS, F020HS, Series 20, FC20, FC22, N140,
N140F, L140, L140F, V140, or V140F may be substituted for the Series 141 Epoxoline
Primer or Topcoat provided that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A to Part B is 2:1 by volume. These application parameters
are Certified for tanks 200 gallons and greater, pipe 14" and greater, fittings 3/4" and
greater, and valves and pumps 3.5" and greater.
[4] Colors: 1255 Beige Primer, WH12 White, 15BL Tank White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% No. 4 Thinner (F041-0004)
Recoat Cure Time and Temperature: 6 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of Series 20, FC20, N140, N140F, L140, L140F, V140,
V140F may be substituted for the Series FC20HS or F020HS Pota-Pox topcoat or primer
provided that both primer and topcoat both meet their Certifed end uses. Mix ratio of
Part A:Part B is 1:1 by volume.
[5] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 15 (maximum of 5 mils per coat)
Maximum Thinner: 5% Tnemec No. 49 Thinner by volume
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140 provided that both primer and topcoat meet
their individual Certified end uses. Series 44-700 accelerator (Part C) may be added up
to 4 fluid ounces per two mixed gallons of L140 Parts A and B. Mix ratio of A:B is 1:1
by volume.
[6] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 2-3
Sequence of coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 15 (maximum of 5 per coat)
Maximum Thinner: 5% Tnemec No. 49 by volume
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
their individual Certified end uses. Mix ratio of Part A to Part B is 1:1 by volume.
[9] Color: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 1-3
Maximum Field Use Dry Film Thickness (in mils): 1 coat - 10, 2-3 coats - 18
Maximum Thinner: 5% Tnemec No. 4 by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comment: Mix ratio of Part A to Part B is 1:1 by volume. Series 44-700 (Part C)
may be added up to 4 fl. oz. per gallon. Any listed color of Series 20, FC20, N140,
N140F, L140, L140F, V140F, 22 and 141 may be substituted as a topcoat or primer for
Series V140 provided that both primer and topcoat meet their individual Certified end
uses.
[10] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 00WH White
Number of Coats: 1-3
Maximum Field Use Dry Film Thickness (in mils): 1 coat: 10; 2-3 coats: 18
Maximum Thinner: 5% Tnemec #4 by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Any listed color of
Series 20, FC20, N140, N140F, L140, L140F, V140, 22, and 141 may be substituted as a
topcoat or primer for Series V140F provided that both primer and topcoat meet their
individual Certified end uses.
[11] Colors: 1216 Grayish-Green
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F
Special Comment: Series 44-710 may be added up to 4 fl. oz/gal. Approved for use as a
primer with any NSF Certified Tnemec topcoat or coating system provided that both primer
and topcoat meet their individual Certified end uses.
[12] Colors: WH06 Off-White
Number of Coats: 1-2
Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
Maximum Field Use Dry Film Thickness (in mils): Primer-10; Topcoat-75
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 72 hours at 75°F
Special Comments: Mix ratio for primers must meet their individual certified parameters.
Mix ratio of A:B is 1:2 by volume for Topcoat. Approved primers are V140 Pota-Pox Plus,
V140F Pota-Pox Plus Fast Cure, Series N140F Pota-Pox Plus Fast Cure, Series 140 Pota-Pox
Plus, FC20HS or F020HS.
[14] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 00WH White,
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec No. 4 Thinner by volume
Recoat Cure Time and Temperature: 12 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any Listed color of Series 141, 22, FC20, N140, or N140F may be
substituted as a topcoat or primer. Mix ratio of Part A:Part B is 1:1 by volume.
[15] Colors: 1200 White, 1212 Gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): Coating only: 80; With fiberglass mat:
95
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass mat S211-0215 and/or addition of fumed silica S211-0211 to coating. Mix ratio
for fumed silica is 0.75:1 by volume. Approved for use with any NSF Certified Tnemec
topcoat or coating system provided that both primer and topcoat meet their individual
Certified end uses.
[16] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
coating system providing that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A:Part B is 70%:30% by volume.
[17] Color: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
use with any NSF Certified Tnemec topcoat or coating system.
[18] Color: 1255 Beige, 15BL Tank White, 1211 Red, 39BL Delft Blue, 00WH White
Number of Coats: 2-3
Sequence of Coats: Any combination of listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec No. 4 by volume
Recoat Cure Time and Temperature: 3 hours at 75°F
Final Cure Time and Temperature: 6 days at 75°F
Special Comments: Any Listed color of series 20, N140, N140F, 141 or 22 may be
substituted as the topcoat or primer. Mix ratio of Part A:Part B is 1:1 by volume.
[19] Colors: WH08 White
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: None
Final Cure Time and Temperature: 24 hours at 75° F
Special Comments: Mix ratio of part A:Part B is 1:2 by volume. Any Listed color of
Series F020, FC20, L140, L140F, N140, N140F, V140, or V140F may be used as a topcoat or
primer for SeriesFC22 Epoxoline.
[20] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft Blue, B5712 Blue,
and B8039 Baker Blue, 00WH Tnemec White, Y2606 Romac Yellow
Number of Coats: 1-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 1 coat - 10, 2-3 coats - 17 mil for
Tnemec Thinner #4 or Thinner #60
Maximum Thinner: 10% Tnemec No. 4 Thinner by volume or 5% Tnemec No. 60 Thinner by
volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any Listed color of Series 20, FC20, 22, FC22, N140F, V140, V140F,
L140, L140F, or 141 may be substituted for the Series N140 Pota-Pox Plus provided that
both primer and topcoat meet their individual Certified end uses. The mix ratio of Part
A:Part B is 1:1 by volume. Part C (Series 44-700 Accelerator) is an optional additive
to Part A in the field and may be added at up to 4 fluid ounces per two mixed gallons of
parts A and B.
[21] Colors: 1211 Red, 1255 Beige,15BL Tank White, 39BL Delft Blue, 35GR Black, B5712 Blue,
B7896 S-B Blue, 00WH Tnemec White, Y2606 Romac Yellow
Number of Coats: 1-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 1 coat - 10, 2-3 coats - 17 mil for
Tnemec Thinner #4 or Thinner #60
Maximum Thinner: 10% Tnemec No. 4 Thinner by volume or 5% Tnemec No. 60 Thinner by
volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any Listed color of Series 20, FC20, 22, FC22, N140, V140, V140F,
L140, L140F or 141 may be substituted for the Series N140F Pota-Pox Plus provided that
both primer and topcoat meet their individual Certified end uses. The mix ratio of Part
A: Part B is 1:1 by volume.
|
||||
|
Coatings - Valve |
||||
| 22 Epoxoline[1] | >= 1/2" | CLD 23 | EPOXY | |
| Series 1 Omnithane 1216 Grayish-Green[11] | >= 4" | CLD 23 | PUR | |
| Series 141 Epoxoline[2] | >= 2" | CLD 23 | EPOXY | |
| Series 141 Epoxoline[3] | >= 3.5" | CLD 23 | EPOXY | |
| Series 406 Elastoshield[12] | >= 4" | CLD 23 | PUR | |
| Series F020HS[4] | 1/2" | CLD 23 | EPOXY | |
| Series FC20HS[4] | 1/2" | CLD 23 | EPOXY | |
| Series FC22 Epoxoline[13] | >= 1/2" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[7] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[8] | >= 4" | CLD 23 | EPOXY | |
| V140 Pota-Pox Plus[9] | >= 2.5" | CLD 23 | EPOXY | |
| V140F Pota-Pox Plus Fast Cure[10] | >= 2.5" | CLD 23 | EPOXY | |
[1] Colors: WH11 White, 1255 Beige, 1218 Blue
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:1 by volume.
[2] Colors: 1255 Beige, WHO3 White, 1211 Red Primer, B2506 DeZurikBlue, B7011 Crispin Blue,
33GR Gray, 35GR Black, and 39BL Delft Blue, B2592 RAL 5009 Azurblau
Number of Coats: 1-3
Sequence of Coats: Any order
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec No. 4 Thinner or 5% Tnemec No. 60 Thinner
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: This application is to be used with pipes 10" and greater, fittings
1/2" and greater, valves 2" and greater, and pumps 4" and greater. Any listed color of
FC20HS, F020HS, Series 20, FC20, FC22, N140, N140F, L140, L140F, V140, or V140F may be
substituted for Series 141 Epoxoline topcoat. Mix ratio of Part A to Part B is 2:1 by
volume.
[3] Colors: 1255 Beige, WHO3 White, 1211 Red Primer, 33GR Gray, 35GR Black, 39BL Delft Blue,
B2592 RAL 5009 Azurblau, and and B8039 Baker Blue
Number of Coats: 1-2
Sequence of Coats: Any order
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% Tnemec #4 Thinner or 5% Tnemec #60 Thinner
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of FC20HS, F020HS, Series 20, FC20, FC22, N140,
N140F, L140, L140F, V140, or V140F may be substituted for the Series 141 Epoxoline
Primer or Topcoat provided that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A to Part B is 2:1 by volume. These application parameters
are Certified for tanks 200 gallons and greater, pipe 14" and greater, fittings 3/4" and
greater, and valves and pumps 3.5" and greater.
[4] Colors: 1255 Beige Primer, WH12 White, 15BL Tank White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 10% No. 4 Thinner (F041-0004)
Recoat Cure Time and Temperature: 6 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Any listed color of Series 20, FC20, N140, N140F, L140, L140F, V140,
V140F may be substituted for the Series FC20HS or F020HS Pota-Pox topcoat or primer
provided that both primer and topcoat both meet their Certifed end uses. Mix ratio of
Part A:Part B is 1:1 by volume.
[7] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, Y2606 Romac Yellow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[8] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 39BL Delft Blue, 35GR Black, B2506
DeZurik Blue, B7896 S-B Blue, 00WH Tnemec White, Y2606 Romac Yallow
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume.
[9] Color: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 1-3
Maximum Field Use Dry Film Thickness (in mils): 1 coat - 10, 2-3 coats - 18
Maximum Thinner: 5% Tnemec No. 4 by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comment: Mix ratio of Part A to Part B is 1:1 by volume. Series 44-700 (Part C)
may be added up to 4 fl. oz. per gallon. Any listed color of Series 20, FC20, N140,
N140F, L140, L140F, V140F, 22 and 141 may be substituted as a topcoat or primer for
Series V140 provided that both primer and topcoat meet their individual Certified end
uses.
[10] Colors: 1211 Red, 1255 Beige, 15BL Tank White, 00WH White
Number of Coats: 1-3
Maximum Field Use Dry Film Thickness (in mils): 1 coat: 10; 2-3 coats: 18
Maximum Thinner: 5% Tnemec #4 by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Any listed color of
Series 20, FC20, N140, N140F, L140, L140F, V140, 22, and 141 may be substituted as a
topcoat or primer for Series V140F provided that both primer and topcoat meet their
individual Certified end uses.
[11] Colors: 1216 Grayish-Green
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F
Special Comment: Series 44-710 may be added up to 4 fl. oz/gal. Approved for use as a
primer with any NSF Certified Tnemec topcoat or coating system provided that both primer
and topcoat meet their individual Certified end uses.
[12] Colors: WH06 Off-White
Number of Coats: 1-2
Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
Maximum Field Use Dry Film Thickness (in mils): Primer-10; Topcoat-75
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 72 hours at 75°F
Special Comments: Mix ratio for primers must meet their individual certified parameters.
Mix ratio of A:B is 1:2 by volume for Topcoat. Approved primers are V140 Pota-Pox Plus,
V140F Pota-Pox Plus Fast Cure, Series N140F Pota-Pox Plus Fast Cure, Series 140 Pota-Pox
Plus, FC20HS or F020HS.
[13] Colors: WH08 White
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: None
Final Cure Time and Temperature: 24 hours at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:2 by volume. Any Listed color of
series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
|
||||
Number of matching Manufacturers is 1
Number of matching Products is 82
Processing time was 0 seconds